as the name implies

Answer: ceramic tile ambry: as the name implies, it is the cupboard that makes with ceramic tile. To be exact, the main structural part of the cabinet is the kitchen cabinet made of ceramic tile, aluminum alloy, red brick, cement, etc. The advantages of ceramic tile cabinet: strong, environmental protection, but also meet the waterproof, fireproof, insect proof, scratch resistant function. Ceramic tile cutting cabinet specific steps: production step 1, table base production: first design to determine a good drawing, the key to the production of the table top has two places to pay special attention to: 1 is to pay attention to the mutual accommodation of pipes, the tabletop of ceramic tile cabinet can not tightly squeeze the upper and lower water pipes, 2 is to strictly determine the exact position and specific reserved size of sink and stove, so as to ensure the sink and stove Embedded. Production step 2, bricklaying; this is the main body of the tile cabinet crevice, the size requirement is not very strict, the error should not exceed 1 / 2 of the thickness of the ash mouth, but the level must be accurate, and attention should be paid to the size of the ash hole of the ceramic tile, so as to prepare for the later tiling, the crevice near the wall and the ground elevation, because the thickness of the red brick is about 55 When the thickness is 100, it is necessary to add fillers on the inside so that there is an appropriate margin for the external tiles when pasting. Cement can be added to the head of cement board or broken bricks. The depth of the front edge of the cabinet floor should be less than 2 cm of the side body, and the thickness of the door board should be reserved. Before bricklaying, it is necessary to do a good job in the sewer and determine the location, and the pipeline safety inspection. Never split Crack or because of loose bonding and leakage phenomenon, in bricklaying should also pay attention not to touch the upper and lower pipes, to avoid the loosening of water pipes!Production step 3, tiling: this step is the key in the key, we must use the real skilled craftsman to go! Because the final quality of ceramic tile cabinet is good or bad, whether it is small brick front 45 degree angle cutting to tile paste flatness, as well as the accuracy of each part size, whether the final completed size is accurate, the key is in this step! First determine the transverse length size, according to the length of each part and the size of the tile to determine the specific position of the front tile, to achieve horizontal and vertical, uniform brick corner, especially the two sides of the wall corresponding to the drawer of the middle device, especially to be flat and accurate. In order to ensure the high flatness of the wall, 500 * 500 ceramic tile with the same color as the exposed ceramic tile can be selected to paste inside , which can reduce the difficulty of operation and clean the interior of the cabinet in the future. Generally, there is a 3mm gap in the ceramic tile gap, which can be grasped with a cross. After pasting, the gap will be treated rotary damper supplier with sealant. Production step 4, internal framework: after the completion of the main body of the ceramic tile, it is the internal framework of the organic system, including the upper body of the partition area inside. The reason why the plate is used for partition instead of the brickwork is two main points: 1. Reduce the waste of space; 2. Enlarge the storage function of the small space on both sides; 2. Fix the door panel in the future; 3. Reduce the length of the laminate formed without division. If the laminate is too long, it will be too long Increase the probability of bending deformation due to heavy pressure. The frame facade partition state of other kitchens can be determined by the design size of each kitchen! In order to prevent the erosion of water vapor, it is better to choose the material with good waterproof performance, plastic rotary damper supplier such as shirt wood integrated wood, etc., and the height and size of cushion material of drawer and laminateThe calculation should be as accurate as possible to avoid empty or skew when the drawer and laminate are installed. Production step 5, above: after the above work is completed, the table can be made. Annex: materials to be purchased for ceramic tile cabinet: 140 pieces of red brick, a number of sand and stone cement, 136 pieces of 100 * 100 facade small bricks, 15 pieces of 500 * 500 ordinary ceramic tiles, 134 pieces of 100 * 100 surface tiles, 15 pieces of 200 * 55 front arc type bricks, 15 pieces of lower edge brick, a bag of joint filling agent, and a bucket of 108 glue. 2440 * 1220 Glulam 1. There are 5 pieces, 6 right angle pieces, 6 8 mm wood round rods, 52 6 mm expansion pipes, 80 40 fast wires, 50 30 fast sliding door damper factory wires, a bag of 16 fast wires, 30 m ribbed steel, 3.7 M2 door panel, 3.2 m hat line, 3 pairs of three drawer slide rails, 14 handles and 22 damping door hinges. Tools needed: plumb, white rope, wooden trowel, peach spade, steel trowel, metal chopper, marble saw, bucket, square groove, two large core plates (it is better to use 60 square aluminum alloy or square steel when making table top), one impact drill, one hand drill, one electric saw, plastic film or nickel paper film One piece, one straw curtain, one piece of wood with a length of 70cm and two pieces of 502 glue.