how much is Shaanxi elevator shaft inorganic fiber spraying?

how much is Shaanxi elevator shaft inorganic fiber spraying? Inner Mongolia inorganic fiber spraying: hard inorganic fiber spraying, inorganic fiber acoustic insulation spraying, TC / F-16 ultra-fine inorganic fiber thermal insulation and sound absorption spraying, etc. The spraying fiber cotton and adhesive shall be sampled for inspection. The fiber cotton shall be dry and free of caking. Even the cotton remaining on the ground must be collected with a dustpan and cleaned to a clean state before construction. 7 the position after spraying shall be flat, that is, the pressing plate shall be used for flattening before fiber curing. 8 the nozzle shall be cleaned carefully after each spraying; The thermal insulation fiber coating after spraying shall be well ventilated, dry and maintained. After curing for 72 hours, finishing, decoration and other processes can be carried out; 10. The construction site after spraying shall be cleaned up in time, and the rebound material shall be bagged and removed from the site, and the basement ceiling shall be insulated; the equipment room and elevator shaft shall be insulated; the profiled steel sheet roof panel shall be insulated; the abnormal circular and arched roof bottom shall be insulated; Gymnasium, museum, exhibition hall, natatorium, library sound absorption and heat preservation; theater, church, music stop, studio, conference hall, pick up table sound absorption and heat preservation; raw material appearance quality inspection: before construction, spray fiber cotton and adhesive shall be sampled for inspection, fiber cotton shall be dry without caking, white without dirt, and adhesive shall be free of layering, foaming, deterioration and discoloration. The Inner Mongolia vitrified bead thermal insulation mortar is used as the thermal insulation layer, and a layer of anti crack mortar with waterproof, anti permeability and anti crack performance is applied on the thermal insulation layer, which is combined with the thermal insulation layerIt forms a complete system of heat sbssteelstructure preservation and insulation, crack resistance, fire prevention and impermeability. The system not only has good thermal insulation performance, but also has excellent thermal insulation and fire protection performance, and can prevent insect and ant erosion. It is a new building thermal insulation material, and has a large number of engineering practices. The vitrified micro bead insulation system is suitable for the internal and external insulation plastering works of reinforced concrete, aerated concrete, block, sintered brick and non sintered brick walls of multi-storey and high-rise buildings, as well as the fire insulation works of basement, garage, stair, corridor and fire passage, as well as the insulation renovation works of old buildings. The characteristics of vitrified microspheres: lightweight aggregate vitrified steel shed roof trusses microspheres are inorganic glass mineral materials, volcano rock is crushed into ore, and processed by special puffing process. The products are irregular spherical granules, the interior is cavity structure, the surface is glazed and sealed, and the physical and chemical properties are stable. It has light weight, heat insulation, fire resistance, high and low temperature resistance, anti-aging and small water absorption. It can replace many traditional lightweight aggregates such as fly ash, glass, ordinary expanded perlite, polystyrene particles, etc? Vitrified micro bead thermal insulation mortar can be used indoors and outdoors, but most of them are used for indoor thermal insulation, such as staircases, basements, garages, partition walls or external wall fire barriers. If it is used alone in the external wall, it needs to be prefab aircraft hangars less than 10 cm if it wants to achieve 65% energy-saving effect, which is not convenient for construction. It is suggested that it can be combined with external wall thermal insulation materials Heat preservation, reaching the requirements of heat preservationIt can achieve A-level fire protection. Which is better, the expansion and vitrification bead thermal insulation mortar or the vitrification bead thermal insulation board? Each has its own advantages and disadvantages. The vitrified bead thermal insulation mortar refers to the thermal insulation material arriving at the construction site, which is mixed with water by machinery, and then plastered on the base layer by layer by workers. The second layer can only be plastered after the first layer has a certain strength. The disadvantage is that the construction period is relatively long, and the advantage is that the material utilization rate is high. The glass bead insulation board is a semi-finished product. The board can be directly used on the wall to use bonding mortar to splice according to the requirements. The advantage is that the construction period is short, but because of splicing, the disadvantage is that the material loss is large. According to the requirements of site drawings, in general, it is recommended to use vitrified micro bead thermal insulation mortar. Curing time of test block under the same conditions: construct a test block on the wall for 3 days, 7 days and 14 days respectively, and observe the strength of mortar. Good strength, good quality. Inner Mongolia inorganic fiber spraying material is a class a non combustible fiber cement plate made of raw wood pulp fiber, fine quartz sand, Portland cement, additives, water and other materials. After being processed in the factory, it is applied to interior and exterior wall decoration with facing and waterproof treatment. Inorganic precoating board does not contain harmful substances such as asbestos and formaldehyde, with thickness of 6-10 mm, high flatness and good weather resistance. It is mainly used in various lining boards, internal partition walls, ceilings, toilets, kitchens and other wet areas. As a kind of green, environmental protection and energy-saving material, inorganic precoating board is widely used in various construction fields, such as table panel, door, cabinet, wardrobe and so on, because of its excellent characteristics. And guard board, lining board, etc. Due to theUnique advantages, very suitable for fire, moisture, environmental protection and other high demand places, schools, kindergartens, precision workshops, R & D rooms, subway and residential interior and exterior walls, ceiling and partition walls. Inorganic precoating board makes up for many shortcomings of metal decoration, natural stone, glass and other decorative materials and coatings in the application of internal and external walls, which conforms to the industrial production development direction of high-performance and mechanized installation of building materials. The quality of external thermal insulation project is related to the beauty and safety of the building facade, which is a social sensitive point. External insulation engineering is the base of external decoration layer in design, and its quality problems directly affect the effect of external facade. In recent years, the "falling off" of external thermal insulation occurred all over the country, which is very easy to cause customer complaints. The thermal insulation project mainly includes four parts of external wall, roof, ground and floor and the requirements of thermal insulation structure. In the cost of construction and installation (excluding the thermal insulation structure part), it is next to the main works, installation works, doors and windows works. Therefore, the design of thermal insulation engineering at least needs to meet the four requirements of building energy conservation, fire prevention, quality and cost, and collaborative management is of great importance. In order to solve this problem, it is recommended to use inorganic fiber spraying. Inner Mongolia inorganic fiber spraying, like the skin, closely adheres to the building base to form a sealed overall jointless spraying layer. Reducing energy consumption in building energy conservation and heat preservation is a product. A product has three functions of fire prevention and non combustion, energy conservation and heat preservation, sound absorption and noise reduction, which amazes visitors. Inorganic fiber spraying is widely used in the fields of construction, ship equipment, sound absorption of tunnel engineering, fire insulation of steel structure engineering and fire insulation of industrial kilnsAll of them have applications.